Embed responsive QSP slides (Ready-to-go slides)


My two previous posts about QSP slides, the focus was on non-responsive projects:

All QSP projects have also a responsive version, created with the Fluid Boxes workflow. To embed such a slide, you'll  an extra difficulty: how will the fluid boxes – both on master slides and slides – behave?  In this blog that extra problem is discussed, including tips to avoid problems. Supposed is that you have read the two previous articles – for the basic knowledge. First recommendation ‘NEVER’ use the switch to Destination theme for a Fluid Boxes project when inserting a QSP slide in a custom responsive project.

Master slides – Tips

All responsive QSP projects have a bunch of master slides. Those master slides have fluid boxes setup.  Setup can be totally different from the non-responsive projects with the same name. Look at the 'Wired' projects: lot of master slides in the responsive version, no master slides except the necessary 6 in the non-responsive version. As you may have deducted from my previous posts,  the NAME of the master slide used for an embedded QSP slide is very important. If the same name has been used in the receiving (destination) project, extra care is needed. For your use I have created a table comparing Master slide names used in the 5 available QSPs (at this moment: September 2019).  You can download the pdf (was quite a lot of work to create it, please show respect for the protection built in).

QSP MasterSlides

In the table some cells are identified in a special way:

  • If the same master slide name is used twice in the QSP, both numbers  are in the same cell, red font on  a grey background. This is a very worrying situation, not sure why the developers did use dual names.

  • Some master slide names appear in several QSPs. If they are identical they are bolded and red for the projects where it is the case. Italic names point to master slides similar to others, but with a slightly different name.

I didn’t include the quizzing master slides. They rarely have been edited a lot (except for the Results slide) and follow the rules I explained in this older post ‘Quiz Slides and Fluid Boxes‘. You could extend the table with the master slide names in your project if you try to embed QSP slides in a company project with an existing theme.

Even master slides with same name, can have a totally different Fluid Boxes setup. The Master slide 'Objectives' is present in 3 QSPs. Have a look at the fluid boxes setup for this Master slides in the projects Aspire, League and Wired.

Aspire's master slide, as you can see, has a rather simple Fluid Boxes setup. The slide ‘Course Objectives’ which is based on this master slide didn’t add supplementary fluid boxes.  That is the case for most slides in the QSPs, only using the Fluid Boxes defined on the master slide. The slide provides 4 topics (Objectives) all in one Fluid Box to the left.

In this master slide of the 'League' project, a lot more Fluid Boxes have been defined. In the screenshot the boxes FB_956 and FB_957 have been collapsed. Their setup is similar to the one shown under FB_955. This master slide provides 3 topics, each in its Fluid Box. As with the Aspire project, the Slide ‘Objectives’, based on this master slide, doesn’t have extra Fluid boxes.

The 'Wired' master slide has the most complicated setup. It is impossible to show the full setup for this master slides. The collapsed FB’s at the bottom each have 5 vertical fluid boxes. No extra FB’s wer added n the slide ‘Objective’. Aspire had 4 topcis (in 1 FB), League had 3 in an individual FB, but Wired has 5 topics. .

You can imagine what happens when you switch from source to destination theme for an inserted slide where both themes use a master slide with an identical name. Have a look at the mess in this example. After inserting the described master slide from the Aspire project, I applied the Wired theme to it. Result, without any warning:

Not only are the objectives not getting into the appropriate FB, the green topics text is not in a Fluid box at all. You will have to move them manually into fluid boxes, and probably delete a lot of (empty) fluid boxes. That is cumbersome work, especially since the FBs are defined on the master slide. That means they cannot be deleted on the slide itself..


For responsive project to brand embedded QSP slide, please follow the step-by-step plan to add a fitting Master slide to the project theme, as described in ‘Embed QSP slides‘. Double-check the name of the Master slide, if it is an existent name in your project, first edit that name in the  QSP theme. That way you will avoid a disaster like I showed above with master slides using the same name.

Feel free to use the pdf I provided with an overview of master slide names for the present responsive QSPs. Beware: there may still be typos, please report them.